Arduino
Showing all 23 resultsSorted by popularity
-
-
All Products, Arduino Boards
Arduino Uno R3 SMD Compatible Development Board(Without cable)
- Microcontroller ATmega328 (SMD) – Interface CH340G
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 5-20V
- Digital I / O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins: 6
SKU: IK-112 -
All Products, Accessories, Motors & Mechanicals, Power Supply
L298n Motor Driver 2A Based Module – Good Quality
All Products, Accessories, Motors & Mechanicals, Power SupplyL298n Motor Driver 2A Based Module – Good Quality
- Current Sense for each motor.
- Heatsink for better performance.
- Power-On LED indicator.
- Double H bridge Drive Chip: L298N.
- Operating Voltage(VDC): 5~35
- Peak Current (A): 2
- Continuous Current (A): 0-36mA
- No. of Channels: 2
- Over-Current Protection (A): Yes
- Thermal Protection: Yes
SKU: IK-132 -
All Products, Arduino Boards
Arduino Nano R3 Compatible Board with CH340 chip(Unsoldered)
- Operating Voltage (logic level): 5V
- With Soldered Connector
- 8 analog inputs ports: A0 ~ A7
- 14 Digital input / output ports: TX, RX, D2 ~ D13
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
SKU: IK-115 -
-
All Products, Arduino Boards
Arduino Uno R3 SMD Compatible Development Board(With cable)
- Microcontroller ATmega328 (SMD) – Interface CH340G
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 5-20V
- Digital I / O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins: 6
SKU: IK-268 -
All Products, Accessories, Accessories, AI Thinker WiFi Module, ESP Boards
USB TO UART TTL 5V 3.3V FT232RL Download Cable To Serial Adapter Module For Arduino Standard Quality
All Products, Accessories, Accessories, AI Thinker WiFi Module, ESP BoardsUSB TO UART TTL 5V 3.3V FT232RL Download Cable To Serial Adapter Module For Arduino Standard Quality
- Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini
- Original FTDI FT232 chip, stable performance
- USB power has current protection, using 500MA self-restore fuse
- RXD/TXD transceiver communication indicator
- With power, sending, receiving indicator, working status LED indicators
- Mini USB Port Connection
- Support 3.3V, 5V
SKU: IK-146 -
-
All Products, Accessories, Accessories, Arduino, Development Boards, Miscellaneous, Sensors
ADS1115 16-Bit ADC- 4 Channel with Programmable Gain Amplifier Standard Quality
All Products, Accessories, Accessories, Arduino, Development Boards, Miscellaneous, SensorsADS1115 16-Bit ADC- 4 Channel with Programmable Gain Amplifier Standard Quality
- Wide Supply Range: 2.0v To 5.5v
- Low Current Consumption
- Continuous Mode: Only 150µa Single-shot
- Auto Shut-down
- Programmable Data Rate: 8SPS to 860SPS
- It has Internal low-drift voltage reference
SKU: IK-172 -
All Products, Accessories, Arduino, Arduino Boards, Arduino Shields
I2C Bi-Directional logic Level Converter- 4 Channel
All Products, Accessories, Arduino, Arduino Boards, Arduino ShieldsI2C Bi-Directional logic Level Converter- 4 Channel
- Material: ABS + metal
- Dimensions: 16 x13 x 3 (L x W x H) mm
- Weight: 2gm
- Mutual transform between 5V TTL and 3.3V TTL
- Four channels of logic and high voltage low voltage logic can two-way transform
- Portable and lightness, with 2 rows 6 pin contact pins
SKU: IK-160 -
All Products, Accessories, Keyboard & Mouse, Pressure/Touch, Switches & Keypads
4×4 Matrix Keypad Membrane Switch for Arduino, ARM and other MCU
All Products, Accessories, Keyboard & Mouse, Pressure/Touch, Switches & Keypads4×4 Matrix Keypad Membrane Switch for Arduino, ARM and other MCU
- Ultra-thin design & adhesive backing provides easy integration to any project
- Excellent price-performance ratio
- Easy communication with any microcontroller
- 5 pins 2.54mm pitch connector, 4x 4type 16 keys.
- Sticker can peel off for adhesive mounting.
- Operating Voltage (V): 12 DC
SKU: IK-138 -
All Products, Accessories, Clock & Timer ICs, RFID/NFC
Real Time Clock RTC DS1307 Module AT24C32 without Battery Standard Quality
All Products, Accessories, Clock & Timer ICs, RFID/NFCReal Time Clock RTC DS1307 Module AT24C32 without Battery Standard Quality
- Two-wire I2C interface.
- Hour: Minutes: Seconds AM/PM.
- Day Month, Date – Year.
- DS1307-based RTC (Battery not include).
- 1Hz output pin.
- Available in 8-pin DIP or SOIC
SKU: IK-122 -
All Products, Accessories, AI Thinker WiFi Module, Miscellaneous
CP2102(6-pin) USB 2.0 to TTL UART serial converter
All Products, Accessories, AI Thinker WiFi Module, MiscellaneousCP2102(6-pin) USB 2.0 to TTL UART serial converter
- Brand new and high quality
- Included USB transceiver, without external circuit device
- With 3.3V and 5V dual power output
- With three LEDs: power indicator, data reception indicator, the data transmission indicator, working status
- Meets the USB2.0 specification requirements
- With self-recovery fuse. In the event of the accidental short circuit, it can effectively protect your computer USB port and Downloader
- Asynchronous serial data bus compatible with all handshake and modulation controller interface signals
- The supported data format is 8 data bits, 1 stop bit and parity bits
SKU: n/a -
Accessories, AI Thinker WiFi Module, All Products, Miscellaneous
CH340G USB To TTL(Serial) Converter For Arduino Nano Raspberry Pi
Accessories, AI Thinker WiFi Module, All Products, MiscellaneousCH340G USB To TTL(Serial) Converter For Arduino Nano Raspberry Pi
- Built-in USB to TTL Transfer chip.
- Designed to be used for USB to TTL electronic projects.
- TTL interface output, easy to connect to your MCU.
- Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device.
- The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC
- Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit system)
SKU: n/a -
All Products, Arduino Shields, Motor Drivers, Stepper Motor/ Controller
A4988 driver Stepper Motor Driver at Best Price
All Products, Arduino Shields, Motor Drivers, Stepper Motor/ ControllerA4988 driver Stepper Motor Driver at Best Price
- Supply Voltage : 8-35 VDC.
- Current : 1.0A (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
SKU: IK-216 -
All Products, Accessories
Transparent Acrylic Case For Arduino UNO R3 at Best Price
- Protective case of Arduino Uno.
- Color: Transparent.
- Fastened by eight screws.
- Made by high grade acrylic.
- Provides excellent protection, with fashion appearance.
- Unique design for Uno with pin leakage, which provides easy connection to other components.
SKU: IK-222 -
All Products, Arduino, Arduino Boards
Arduino LilyPad 328 Main Board Standard Quality
- Microcontroller: ATmega168 or ATmega328V
- Operating Voltage: 2.7-5.5 V
- Digital I/O Pins: 14
- PWM Channels: 6
- Analog Input Channels: 6
- DC Current per I/O Pin: 40 mA
- Board will run from 2V to 5V.
- The latest version of the LilyPad supports automatic reset for even easier programming.
- The back side of the LilyPad is now completely flat!
SKU: IK-245 -
All Products, Arduino Shields
L293D Motor Driver Shield For Arduino Standard Quality
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
SKU: IK-133 -
All Products, Arduino Shields
CNC Shield V3 for Engraving Machine 3D Printer A4988 DRV8825 Driver Expansion Board
All Products, Arduino ShieldsCNC Shield V3 for Engraving Machine 3D Printer A4988 DRV8825 Driver Expansion Board
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Coolant enable
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
SKU: IK-109 -
All Products, Arduino Boards
Arduino Mega 16U2 Original board 2560 R3 with Compatible USB Cable
- 54 Digital I/O terminals (14 of which have programmable PWM outputs).
- 16 Analog Inputs.
- 4 UARTs (hardware serial ports).
- 16 MHz crystal clock.
- Operating voltage: 6 ~ 12v.
- Dimensions: 110 x 53 x 15 mm.
SKU: IK-114 -
All Products, Arduino Boards
Pro Mini ATMEGA328P 5V/16M (Official Version)
- Microcontroller: ATmega328P
- Circuit Operating Voltage: 5V
- Clock frequency: 16MHz.
- 6 PWM port: D3, D5, D6, D9, D10, D11.
- Use For Atmel Atmega328P-AU microcontroller.
- Support serial download.
- Support 9V battery.
- A pair of TTL level serial port transceiver : RX / TX.
SKU: IK-117
