Subtotal: ₹160.00
Motor Driver
Showing all 7 resultsSorted by popularity
-
All Products, Accessories, Motors & Mechanicals, Power Supply
L298n Motor Driver 2A Based Module – Good Quality
All Products, Accessories, Motors & Mechanicals, Power SupplyL298n Motor Driver 2A Based Module – Good Quality
- Current Sense for each motor.
- Heatsink for better performance.
- Power-On LED indicator.
- Double H bridge Drive Chip: L298N.
- Operating Voltage(VDC): 5~35
- Peak Current (A): 2
- Continuous Current (A): 0-36mA
- No. of Channels: 2
- Over-Current Protection (A): Yes
- Thermal Protection: Yes
SKU: IK-132 -
All Products, Miscellaneous, Power Supply, Switches & Keypads
5-36V Switch Drive High-Power MOSFET Trigger Module Standard Quality
All Products, Miscellaneous, Power Supply, Switches & Keypads5-36V Switch Drive High-Power MOSFET Trigger Module Standard Quality
This 5-36v Switch Drive High-power MOSFET Trigger Module can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, PWM, motor speed control, lamp brightness. etc.
SKU: IK-252 -
-
All Products, Stepper Motor/ Controller
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
All Products, Stepper Motor/ Controller16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: IK-127 -
All Products, Arduino Shields, Motor Drivers, Stepper Motor/ Controller
A4988 driver Stepper Motor Driver at Best Price
All Products, Arduino Shields, Motor Drivers, Stepper Motor/ ControllerA4988 driver Stepper Motor Driver at Best Price
- Supply Voltage : 8-35 VDC.
- Current : 1.0A (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
SKU: IK-216 -
All Products, Arduino Shields
L293D Motor Driver Shield For Arduino Standard Quality
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
SKU: IK-133 -
All Products, Arduino Shields
CNC Shield V3 for Engraving Machine 3D Printer A4988 DRV8825 Driver Expansion Board
All Products, Arduino ShieldsCNC Shield V3 for Engraving Machine 3D Printer A4988 DRV8825 Driver Expansion Board
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Coolant enable
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
SKU: IK-109
