Subtotal: ₹130.00
Motors & Mechanicals
Showing all 23 resultsSorted by popularity
-
All Products, Accessories, Motors & Mechanicals, Power Supply
L298n Motor Driver 2A Based Module – Good Quality
All Products, Accessories, Motors & Mechanicals, Power SupplyL298n Motor Driver 2A Based Module – Good Quality
- Current Sense for each motor.
- Heatsink for better performance.
- Power-On LED indicator.
- Double H bridge Drive Chip:Â L298N.
- Operating Voltage(VDC): 5~35
- Peak Current (A): 2
- Continuous Current (A): 0-36mA
- No. of Channels: 2
- Over-Current Protection (A): Yes
- Thermal Protection: Yes
SKU: IK-132 -
-
All Products, BO Motor, Motors & Mechanicals
BO Motor Wheel 34mm – Set of 2
- These are the green BO motor wheels (2pcs)
- These wheels are of good quality
- The diameter of the wheel: 34mm
- The width of the wheel: 10mm (1cm)
- Screws can be fitted into the axle socket mounted from the front for keeping the wheel in place
- These wheels are used for robotics race
SKU: IK-230 -
All Products, DC Fans, Gear Motor, Motors & Mechanicals
N20-6V-60 RPM Micro Metal Gear-box DC Motor
- This is a DC Mini Metal Gear Motor, ideal for making robots.
- Lightweight, high torque and low RPM.
- Fine craftsmanship, durable, not easy to wear.
- With excellent stall characteristics, can climb hills easily.
- You can also easily mount a wheel on the motor’s output shaft.
SKU: IK-219 -
All Products, BO Motor, Motors & Mechanicals, Robot Kits
65mm Robot Wheel for BO Motors (Yellow)
- Tire with sponge liner for more strength
- With upgraded tire tread for greater friction
- New design wheel for better combination with the motor
- Diameter: 65 mm
- Width : 28 mm
- The material of Wheel: High-strength plastic
- The material of Tyre: Rubber
- Color: Yellow
SKU: IK-207 -
-
All Products, Stepper Motor/ Controller
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
All Products, Stepper Motor/ Controller16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: IK-127 -
-
All Products, Motors/ESC/Controller, Servo Motor/Controller
Digital Multi Servo Tester ESC RC-1 Consistency CCPM Master Speed Control
All Products, Motors/ESC/Controller, Servo Motor/ControllerDigital Multi Servo Tester ESC RC-1 Consistency CCPM Master Speed Control
- Operating Voltage: DC 4.8-6V
- Offer 3 modes to check servos or ESC
- The Manual Mode allows you to turn the knob to different speeds and check the reaction time
- The Neutral mode makes the servo go back to the neutral point
- The Automatic ’’Window Wiper’’ Mode makes the servo swing like a window wiper in the largest angle possible
- Connect to up to 3 servos simultaneously
SKU: IK-128 -
-
All Products, Arduino Shields, Motor Drivers, Stepper Motor/ Controller
A4988 driver Stepper Motor Driver at Best Price
All Products, Arduino Shields, Motor Drivers, Stepper Motor/ ControllerA4988 driver Stepper Motor Driver at Best Price
- Supply Voltage : 8-35 VDC.
- Current : 1.0A Â (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
SKU: IK-216 -
-
All Products, BO Motor
60 RPM BO Motor – Straight
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5 (Double D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 100 RPM
- Rated Torque: 1 Kgcm
SKU: IK-208 -
All Products, BO Motor
100 RPM BO Motor- L Shape
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5 (Double D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 100 RPM
- Rated Torque: 0.8 Kgcm
SKU: IK-210
