Shop
Showing 217–240 of 246 resultsSorted by popularity
-
All Products, Buck/Boast Converter, DC-DC Converter
150W DC-DC Boost Converter 10-32V to 12-35V 6A Step-Up Adjustable Power Supply
All Products, Buck/Boast Converter, DC-DC Converter150W DC-DC Boost Converter 10-32V to 12-35V 6A Step-Up Adjustable Power Supply
- Input voltage :10-32V
- Output voltage: 12-35V (adjustable)
- Output Current: 10A (MAX)
- Input Current: 16A (MAX) (Please enhance heat dissipation if more than 10A)
- The non-isolated step-up power conversion module
- Onboard LED illuminates when the voltage is applied to the module
- Equips Multi-turn Potentiometer.
SKU: IK-248 -
-
All Products, Stepper Motor/ Controller
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
All Products, Stepper Motor/ Controller16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: IK-127 -
-
All Products, Motors/ESC/Controller, Servo Motor/Controller
Digital Multi Servo Tester ESC RC-1 Consistency CCPM Master Speed Control
All Products, Motors/ESC/Controller, Servo Motor/ControllerDigital Multi Servo Tester ESC RC-1 Consistency CCPM Master Speed Control
- Operating Voltage: DC 4.8-6V
- Offer 3 modes to check servos or ESC
- The Manual Mode allows you to turn the knob to different speeds and check the reaction time
- The Neutral mode makes the servo go back to the neutral point
- The Automatic ’’Window Wiper’’ Mode makes the servo swing like a window wiper in the largest angle possible
- Connect to up to 3 servos simultaneously
SKU: IK-128 -
-
All Products, Arduino Shields, Motor Drivers, Stepper Motor/ Controller
A4988 driver Stepper Motor Driver at Best Price
All Products, Arduino Shields, Motor Drivers, Stepper Motor/ ControllerA4988 driver Stepper Motor Driver at Best Price
- Supply Voltage : 8-35 VDC.
- Current : 1.0A Â (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
SKU: IK-216 -
-
All Products, BO Motor
60 RPM BO Motor – Straight
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5 (Double D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 100 RPM
- Rated Torque: 1 Kgcm
SKU: IK-208 -
All Products, BO Motor
100 RPM BO Motor- L Shape
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5 (Double D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 100 RPM
- Rated Torque: 0.8 Kgcm
SKU: IK-210 -
All Products, RF/NRF Module
M177 NRF24L01 2.4GHz Antenna Wireless Transceiver Module
- Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability,
- Particularly suitable for industrial control applications.
- Built-in hardware CRC error detection, Multipoint communication address control.
- Low-power 1.9 ~ 3.6V, only 1uA on Power down mode
- Built-in 2.4Ghz antenna
- Built-in voltage regulator
- Standard DIP Pitch Interface for embedded applications
SKU: IK-139 -
-
All Products, ESP Boards, ESP8266 Boards
ESP8266 Adapter Plate Serial Wireless WIFI Module
- It features reserved land-pattern for the 3.3V regulator
- It has Pinouts on the top layer in black colour.
- Compatible with Latest ESP-12F ESP8266 Wifi Module
- It includes a 10K pull-up resistor populated on PCB.
SKU: n/a -
All Products, ESP Boards, ESP8266 Boards
IoT Board Module ESP-12F ESP8266 Wifi Wireless at Best Price
All Products, ESP Boards, ESP8266 BoardsIoT Board Module ESP-12F ESP8266 Wifi Wireless at Best Price
- Communication interface voltage: 3.3V
- Working current: 240mA(MAX)
- Serial port baud rate: 115200 (default), can be modified to other values by AT command
- Serial communication format: 8N1
- Wireless Network Mode: station / softAP / SoftAP + station
- Wireless criteria: 802.11 b / g / n
- WIFI @ 2.4 GHz, support for WPA / WPA2 security mode
- +19.5dBm output power
SKU: IK-242 -
All Products, ESP Boards, ESP8266 Boards
Transceiver Module Esp-01 Esp8266 serial wifi Wireless Standard Quality
All Products, ESP Boards, ESP8266 BoardsTransceiver Module Esp-01 Esp8266 serial wifi Wireless Standard Quality
- 802.11 b/g/n Standards
- Wi-Fi Direct (P2P), soft-AP
- 1MB Flash Memory
- Integrated low power 32-bit CPU could be used as an application processor
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
SKU: IK-224 -
-
All Products, Accessories
Transparent Acrylic Case For Arduino UNO R3 at Best Price
- Protective case of Arduino Uno.
- Color: Transparent.
- Fastened by eight screws.
- Made by high grade acrylic.
- Provides excellent protection, with fashion appearance.
- Unique design for Uno with pin leakage, which provides easy connection to other components.
SKU: IK-222 -
All Products, Arduino, Arduino Boards
Arduino LilyPad 328 Main Board Standard Quality
- Microcontroller: ATmega168 or ATmega328V
- Operating Voltage: 2.7-5.5 V
- Digital I/O Pins: 14
- PWM Channels: 6
- Analog Input Channels: 6
- DC Current per I/O Pin: 40 mA
- Board will run from 2V to 5V.
- The latest version of the LilyPad supports automatic reset for even easier programming.
- The back side of the LilyPad is now completely flat!
SKU: IK-245 -
All Products, Arduino Shields
L293D Motor Driver Shield For Arduino Standard Quality
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
SKU: IK-133 -
All Products, Arduino Shields
CNC Shield V3 for Engraving Machine 3D Printer A4988 DRV8825 Driver Expansion Board
All Products, Arduino ShieldsCNC Shield V3 for Engraving Machine 3D Printer A4988 DRV8825 Driver Expansion Board
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Coolant enable
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
SKU: IK-109
